Cook Like a Chef | Get 30% off ChefSteps
20 November 2026 · 1:38 watch
Advertisement
How potato pavé is built from thinly sliced potato, butter and cream, why the layers set into a sliceable block, and where the method is most likely to go wrong.
Key takeaways
- Potato pavé is built by shingling thinly sliced potatoes in a lined tin, brushing each layer with melted butter and seasoning, then baking until the layers bind.
- Uniform slices cut to about one-sixth of an inch give even cooking and a block that holds together when cut.
- Tossing the slices in heavy cream before layering helps prevent oxidation while they wait to be assembled.
- A pavé should rest before cutting; cutting it hot causes the layers to slump and separate.
- The dish is effectively a tender interior with crisp edges, and it can be reheated in butter or oil to restore the exterior.
Potato pavé is a layered dish of thinly sliced potato, packed into a tight block and baked until the slices fuse into a sliceable, crisp-edged cake with a soft interior. It is built from very simple ingredients, but the result depends on slice thickness, the fat and dairy used between the layers, and how firmly the block is pressed before and after baking. Its appeal to restaurant kitchens is the contrast it offers: a crisp exterior, a creamy centre and a geometric, mille-feuille look when cut.
The basic construction is a stack of potato slices, each layer brushed with melted butter and seasoned with salt and pepper, repeated until the potatoes are used up. One published method uses Yukon gold potatoes, peeled and sliced on a mandolineMandolineA kitchen slicing tool designed to produce fast, precise and uniform cuts. to roughly one-sixth of an inch, with heavy cream tossed through the slices to stop them oxidising before they are layered. The dish is then baked in a parchment-lined, buttered tin, with the butter used both to grease the pan and to finish each layer. Because the slices are shingled rather than scattered, each layer forms a continuous sheet, and the starch released from the cut surfaces helps the layers bind together as they cook.
Mise en placeMise en PlaceFrench for "everything in its place"; the preparation and organisation completed before service. is mostly about the slicer and the tin. Uniform slices matter more than any other single factor: thick or uneven potato will leave gaps, cook at different rates and fail to release cleanly. Keep the slices in cream until you are ready to layer them, and cut the parchment to fit the base of the tin before you start, so the pavé can be lifted out whole. Use a tin small enough that the layers stand several slices deep; a wide, shallow tin produces a thin, brittle cake rather than a block.
Temperature and time are where the technique is most often misjudged. Bake gently enough that the centre cooks through and the potato becomes tender before the exterior colours, then allow the block to rest before cutting. A pavé cut hot will slump and separate. If the top is pale but the edges are catching, the oven is running hot or the tin is too close to the element. If the centre is wet and the slices slide apart, the potatoes were too thick, the cream was under-used, or the block was not pressed sufficiently before setting.
Once set, a pavé is cut into neat portions, and the cut faces show the layers that give the dish its name. For service, the block can be cut into rectangles, reheated to restore crispness, and finished in a pan with butter or oil so the exterior crisps again. The same layering logic also applies to a more elaborate version that uses a different construction and a laminated, croissant-style form. Some kitchens treat potato pavé as a side for roasts or fish; others present it as a standalone course. The technique is flexible, but it rewards careful slicing, controlled heat and patience before the first cut.
References
Questions from the pass
Frequently asked questions
Why are the potato slices tossed in cream before layering?
The research describes tossing sliced potatoes with heavy cream to prevent oxidation while the slices wait to be assembled. This keeps the cut surfaces pale and gives the layers a cleaner finish once baked, and it means the slices can be prepared ahead without browning before they go into the tin.
What thickness should the potato slices be?
A published method calls for potatoes sliced thinly on a mandoline to about one-sixth of an inch. Uniform thickness matters because it ensures the layers cook at the same rate and bind into a block that can be cut cleanly.
How is the pan prepared for potato pavé?
The tin is greased with butter, lined with parchment cut to fit the base, and greased again. This allows the set block to be lifted out whole. Each layer is also brushed with melted butter and seasoned with salt and pepper as the potatoes are shingled into the tin.
Can potato pavé be made in advance and reheated?
Sources describe the finished pavé as having a crisp exterior and creamy interior, and the ChefSteps material presents it as a dish designed for restaurant service. Reheating it in a pan with butter or oil, as commonly practised in kitchens, is a reasonable way to restore the crisp edges, though the sources do not give a detailed reheating method.
Original video by ChefSteps. The Chef's Circle is the article publisher, not the video creator. This overview is written independently by The Chef's Circle editorial desk — watch the original on YouTube.
Keep reading



